Hand and Power Tool HSE Training
Slide 1: Hand and Power Tool Safety – HSE Training
Presented by: HSE STUDY GUIDE
Date: 26/04/2025
Good morning team!
Hope you all are doing well today.
We’re going to talk about a safety topic that seems simple — but causes thousands of injuries every year: Hand and Power Tool Safety.
Whether you’re cutting, drilling, grinding, or tightening, one small mistake can lead to serious injury. Let’s sharpen our awareness just like we sharpen our tools — and make sure safety comes first.
Slide 2: Objectives of the Training
By the end of today’s session, you’ll understand:
- The difference between hand and power tools
- Common hazards when using tools
- Safe work practices for each type
- Proper inspection and maintenance
- Your responsibility as a user
Slide 3: What Are Hand and Power Tools?
Hand tools are operated manually — examples include:
- Wrenches
- Screwdrivers
- Hammers
- Pliers
Power tools are driven by electricity, compressed air, fuel, or batteries — such as:
- Drills
- Grinders
- Saws
- Nail guns
Different tools — same goal: work smarter and safer.
Slide 4: Why Tool Safety Matters
Injuries from tools may include:
- Cuts and punctures
- Eye injuries
- Electric shock
- Crushed fingers
- Amputations
Most injuries happen due to carelessness, poor maintenance, or lack of training.
Safe tool use is smart tool use.
Slide 5: General Safety Rules for All Tools
- Always inspect tools before use
- Use the right tool for the job
- Never use damaged or defective tools
- Keep tools clean and well-maintained
- Wear appropriate PPE (gloves, goggles, etc.)
- Store tools safely when not in use
Treat every tool like it could hurt you — because it can.
Slide 6: Hand Tool Safety Tips
- Keep cutting edges sharp and handles in good condition
- Never carry tools in your pockets
- Don’t use a wrench as a hammer or vice versa
- Always cut away from your body
- Secure your workpiece — don’t hold it in your hand while cutting or sawing
Small mistakes can lead to big injuries — focus matters.
Slide 7: Power Tool Safety Tips
- Check cords, plugs, and switches before use
- Never remove guards or safety devices
- Ensure proper grounding for corded tools
- Keep your hands and body clear of moving parts
- Don’t force a power tool — let it do the work
Always disconnect tools before changing blades or bits.
Slide 8: Electrical Safety for Power Tools
- Use double-insulated tools where possible
- Never use electrical tools in wet or damp areas
- Inspect extension cords for damage
- Don’t overload circuits
- Use GFCIs (Ground Fault Circuit Interrupters) in outdoor or wet locations
Electricity can’t be seen — but it can be deadly.
Slide 9: Compressed Air Tools
- Use safety clips and retainers
- Check hoses for cracks and wear
- Do not use compressed air to clean clothing or skin
- Bleed off pressure before disconnecting
- Always wear eye and face protection
Compressed air can penetrate the skin — handle it with care.
Slide 10: PPE for Tool Use
- Gloves for sharp or hot materials
- Safety glasses/goggles to protect your eyes
- Face shields for grinding or cutting
- Hearing protection when using loud tools
- Steel-toe boots for heavy materials
Your first defense is proper PPE — wear it every time.
Slide 11: Tool Maintenance and Inspection
- Inspect tools daily before use
- Label and remove damaged tools from service
- Clean tools after use
- Store in dry, secure places
- Keep cutting edges sharp and lubricated as needed
A poorly maintained tool is a hidden hazard.
Slide 12: Unsafe Tool Use Examples
Let’s look at some unsafe practices:
- Using a screwdriver as a chisel
- Grinding without a guard
- Using pliers on a nut instead of a proper wrench
- Running cords through water or across walkways
- Leaving tools lying around
Have you seen these on your site? Let’s talk about how we can stop them.
Slide 13: Real Incident Case Study
Incident:
A worker was using a grinder without the guard and proper face protection. The wheel shattered, and fragments struck his face, causing severe injuries.
What went wrong?
- No guard
- No face shield
- Tool was used without inspection
Takeaway:
PPE and guards exist for a reason — don’t ignore them.
Slide 14: Housekeeping and Storage
- Keep work areas free of clutter
- Clean up spills and tool debris immediately
- Return tools to their proper place after use
- Secure heavy tools properly
- Avoid stacking tools where they can fall
A tidy workplace is a safe workplace.
Slide 15: Your Role in Tool Safety
- Know your tools — get trained
- Inspect tools before use
- Report defective or unsafe equipment
- Never take shortcuts
- Help your coworkers stay safe too
We all have a role in building a safety culture.
Slide 16: Final Reminders
- Use the right tool, the right way, every time
- Respect the power of tools — manual or electric
- Don’t bypass safety guards or procedures
- Stay alert — distraction leads to disaster
- Keep safety sharp — just like your tools
Slide 17: Questions and Discussion
Now it’s your turn!
Have you seen unsafe tool use on site?
Do you have any tips or lessons learned from tool-related incidents?
Let’s share and learn from each other.
Slide 18: Thank You
Thanks, team, for your time and attention today.
Hand and power tools help us do our job — but only when we use them with respect and responsibility.
Let’s commit to using tools safely, every day, on every job.
Follow HSE STUDY GUIDE for more safety updates and awareness tips.
Stay safe and work smart!
Lockout and Tagout Procedure HSE Training
